Merge pull request #1307 from arduino/karlsoderby/giga-r1-update-sept6

[GIGA R1 WiFi] Docs general maintenance

Author: karlsoderby

content/hardware/10.mega/boards/giga-r1-wifi/features.md

@@ -33,7 +33,7 @@ The GIGA R1 WiFi comes with a Murata LBEE5KL1DX-883 radio module for Wi-Fi/Bluet
 <Feature title="MicroPython" image="python">
 The GIGA R1 WiFi has support for MicroPython, which can be set up in just minutes.
 
-<FeatureLink title="Install MicroPython" url="/tutorials/giga-r1-wifi/giga-micropython"/>
+<FeatureLink title="Install MicroPython" url="/micropython/basics/board-installation"/>
 </Feature>
 
 <Feature title="USB" image="usb">

content/hardware/10.mega/boards/giga-r1-wifi/tutorials/cheat-sheet/assets/spipins.png

@@ -639,19 +639,19 @@ void loop() {
 
 The **GIGA R1** features two separate SPI (Serial Peripheral Interface) buses, one is configured on the 6 pin header (ICSP) labelled SPI, and the other is broken out into pin connections on the board.
 
-The first bus (connector), `SPI` uses the following pins:
+The first bus (connector), `SPI1` uses the following pins:
 
 - (CIPO) - D89
 - (COPI) - D90
 - (SCK) - D91
-- (CS) - D10
+- (CS) - unassigned, use any free GPIO for this.
 
-The second bus (header), `SPI1`, uses the following pins: 
+The second bus (header), `SPI5`, uses the following pins: 
 
 - (CIPO) - D12
 - (COPI) - D11
 - (SCK) - D13
-- (CS) - unassigned, use any free GPIO for this.
+- (CS) - D10
 
 For using both SPI buses simultaneously, check out the following example:
 

content/hardware/10.mega/boards/giga-r1-wifi/tutorials/cheat-sheet/cheat-sheet.md

@@ -463,15 +463,15 @@ The GIGA R1 12-bit DAC channels can also be used to read `.wav` files from a USB
 For this example, you will need:
 - A speaker, that has a built in amplifier.
 - A USB mass storage device (USB stick).\*
-- [USBHostMbed5](https://github.com/facchinm/USBHostMbed5) library installed.
+- [Arduino_USBHostMbed5](https://github.com/arduino-libraries/Arduino_USBHostMbed5) library installed.
 
 ***\*USB mass storage devices connected needs to be formatted with the FAT32 as a file system, using the MBR partitioning scheme. Read more in the [USB Mass Storage](/tutorials/giga-r1-wifi/giga-usb/#usb-mass-storage) section.***
 
 ### USB Stick Configuration
 
 The **Arduino_AdvancedAnalog** library contains the necessary functions that enable us to use the advanced capabilities of the GIGA R1 DACs. 
 
-To read `.wav` files from the USB stick we are using the **USBHostMbed5** library. It is important that the USB stick is formatted properly, and that we define its name in the sketch. In this case, we name it `USB_DRIVE`, and is defined like this: 
+To read `.wav` files from the USB stick we are using the **Arduino_USBHostMbed5** library. It is important that the USB stick is formatted properly, and that we define its name in the sketch. In this case, we name it `USB_DRIVE`, and is defined like this: 
 
 ```arduino 
 mbed::FATFileSystem usb("USB_DRIVE");
@@ -501,7 +501,7 @@ Note that to start the sketch, you need to open Serial Monitor due to the `while
 
 #include <Arduino_AdvancedAnalog.h>
 #include <DigitalOut.h>
-#include <USBHostMbed5.h>
+#include <Arduino_USBHostMbed5.h>
 #include <FATFileSystem.h>
 
 AdvancedDAC dac1(A12);
@@ -675,7 +675,7 @@ You can download them from [this link](/resources/misc/giga_audio_examples.zip).
 
 #include <Arduino_AdvancedAnalog.h>
 #include <DigitalOut.h>
-#include <USBHostMbed5.h>
+#include <Arduino_USBHostMbed5.h>
 #include <FATFileSystem.h>
 
 AdvancedDAC dac1(A12);

content/hardware/10.mega/boards/giga-r1-wifi/tutorials/giga-audio/content.md

@@ -5,9 +5,7 @@ author: Karl Söderby
 tags: [MicroPython, dfu-util]
 ---
 
-***Please note that MicroPython support for the GIGA R1 is currently in an experimental phase.***
-
-***To learn more about MicroPython, please visit [MicroPython with Arduino](/learn/programming/arduino-and-python). This article is specific only to the GIGA R1 board.***
+***Please note: MicroPython documentation for all boards has moved to [MicroPython Docs Page](/micropython). Please refer to that page for the most up to date documentation.***
 
 [MicroPython](https://micropython.org/) is an implementation of Python in a *micro* format. It can be installed on the GIGA R1, where instead of compiling and uploading sketches, the board has a built-in interpreter that converts Python code to machine code in runtime.
 
@@ -28,9 +26,9 @@ You will need the following software/tools installed:
 
 ## Installation
 
-Following the steps below will install MicroPython on the **M7** core. 
+***Note: a new tool has been added that makes it a lot easier to install MicroPython on your board. Visit the [MicroPython installation page](/micropython/basics/board-installation) for more information.***
 
-***Please note that after this installation is complete, your board will no longer be detected as an Arduino device. In order to go back to using the Arduino programming environment, you need to reset the board. This is simply done by double tapping the reset button.***
+Following the steps below will install MicroPython on the **M7** core.
 
 **1.** Download the [GIGAR1_MP_FW.dfu](/resources/firmware/GIGAR1_MP_FW.dfu) firmware (latest firmware is always available at the [MicroPython with Arduino](/micropython/) page).
 
@@ -60,6 +58,8 @@ Done parsing DfuSe file
 
 Congratulations! You have now installed MicroPython on the GIGA R1 board.
 
+***Please note that after this installation is complete, your board will no longer be detected as an Arduino device. In order to go back to using the Arduino programming environment, you need to reset the board. This is simply done by double tapping the reset button.***
+
 ## Programming Your Board
 
 To program your GIGA R1 with MicroPython, you will need an editor with support for MicroPython (such as [Arduino Lab for MicroPython](https://labs.arduino.cc/en/labs/micropython) or [Thonny](https://thonny.org/)).