Skip to content

Commit 6f7aa8e

Browse files
karlsoderbykarlsoderby
authored
Merge pull request #1447 from arduino/karlsoderby/nano-33-iot-ds-update
[Nano-33-IoT] GPIO update in datasheet
2 parents 0dd7d88 + d1561c6 commit 6f7aa8e

File tree

1 file changed

+77
-76
lines changed
  • content/hardware/03.nano/boards/nano-33-iot/datasheet

1 file changed

+77
-76
lines changed

‎content/hardware/03.nano/boards/nano-33-iot/datasheet/datasheet.md‎

Lines changed: 77 additions & 76 deletions
Original file line numberDiff line numberDiff line change
@@ -92,11 +92,11 @@ As all Nano form factor boards, Nano 33 IoT and Nano 33 IoT with headers does no
9292
| | Conservative thermal limits for the whole board: | -40 °C ( 40 °F) | 85°C ( 185 °F) |
9393

9494
### Power Consumption
95-
| Symbol | Description | Min | Typ | Max | Unit |
96-
| ------- | ---------------------------------------- | ---- | ---- | ---- | ---- |
97-
| VINMax | Maximum input voltage from VIN pad | -0.3 | - | 21 | V |
98-
| VUSBMax | Maximum input voltage from USB connector | -0.3 | - | 21 | V |
99-
| PMax | Maximum Power Consumption | - | - | TBC | mW |
95+
| Symbol | Description | Min | Typ | Max | Unit |
96+
| ------- | ---------------------------------------- | ---- | --- | --- | ---- |
97+
| VINMax | Maximum input voltage from VIN pad | -0.3 | - | 21 | V |
98+
| VUSBMax | Maximum input voltage from USB connector | -0.3 | - | 21 | V |
99+
| PMax | Maximum Power Consumption | - | - | TBC | mW |
100100

101101
## Functional Overview
102102
### Board Topology
@@ -132,7 +132,7 @@ Communication with NINA W102 happens through a serial port and a SPI bus through
132132
| 21 | GPIO19 | UART RTS | | |
133133
| 24 | PA15 | 29 | GPIO18 | SPI CLK |
134134
| 20 | GPIO22 | UART CTS | | |
135-
| 22 | PA13 | 1 | GPIO21 | SPI MISO |
135+
| 22 | PA13 | 1 | GPIO23 | SPI MISO |
136136
| 21 | PA12 | 36 | GPIO12 | SPI MOSI |
137137
| 31 | PA22 | 23 | GPIO3 | Processor TX 🡺 Nina RX |
138138
| 32 | PA23 | 22 | GPIO1 | Processor RX 🡸 Nina TX |
@@ -194,67 +194,67 @@ All Arduino boards have a built-in bootloader which allows flashing the board vi
194194

195195
### USB
196196

197-
| Pin | **Function** | **Type** | **Description** |
198-
| ---- | ------------ | ------------ | ------------------------------------------------------------ |
199-
| 1 | VUSB | Power | Power Supply Input. If board is powered via VUSB from header this is an Output **(1)** |
200-
| 2 | D- | Differential | USB differential data - |
201-
| 3 | D+ | Differential | USB differential data + |
202-
| 4 | ID | Analog | Selects Host/Device functionality |
203-
| 5 | GND | Power | Power Ground |
197+
| Pin | **Function** | **Type** | **Description** |
198+
| --- | ------------ | ------------ | -------------------------------------------------------------------------------------- |
199+
| 1 | VUSB | Power | Power Supply Input. If board is powered via VUSB from header this is an Output **(1)** |
200+
| 2 | D- | Differential | USB differential data - |
201+
| 3 | D+ | Differential | USB differential data + |
202+
| 4 | ID | Analog | Selects Host/Device functionality |
203+
| 5 | GND | Power | Power Ground |
204204

205205
1. The board can support USB host mode only if powered via the V<sub>USB</sub> pin and if the jumper close to the VUSB pin is shorted.
206206

207207

208208
### Headers
209209
The board exposes two 15 pin connectors which can either be assembled with pin headers or soldered through castellated vias.
210210

211-
| Pin | **Function** | **Type** | **Description** |
212-
| ---- | ------------ | ------------ | ------------------------------------------------------------ |
213-
| 1 | D13 | Digital | GPIO |
214-
| 2 | +3V3 | Power Out | Internally generated power output to external devices |
215-
| 3 | AREF | Analog | Analog Reference; can be used as GPIO |
216-
| 4 | A0/DAC0 | Analog | ADC in/DAC out; can be used as GPIO |
217-
| 5 | A1 | Analog | ADC in; can be used as GPIO |
218-
| 6 | A2 | Analog | ADC in; can be used as GPIO |
219-
| 7 | A3 | Analog | ADC in; can be used as GPIO |
220-
| 8 | A4/SDA | Analog | ADC in; I2C SDA; Can be used as GPIO **(1)** |
221-
| 9 | A5/SCL | Analog | ADC in; I2C SCL; Can be used as GPIO **(1)** |
222-
| 10 | A6 | Analog | ADC in; can be used as GPIO |
223-
| 11 | A7 | Analog | ADC in; can be used as GPIO |
224-
| 12 | VUSB | Power In/Out | Normally NC; can be connected to VUSB pin of the USB connector by shorting a jumper |
225-
| 13 | RST | Digital In | Active low reset input (duplicate of pin 18) |
226-
| 14 | GND | Power | Power Ground |
227-
| 15 | VIN | Power In | Vin Power input |
228-
| 16 | TX | Digital | USART TX; can be used as GPIO |
229-
| 17 | RX | Digital | USART RX; can be used as GPIO |
230-
| 18 | RST | Digital | Active low reset input (duplicate of pin 13) |
231-
| 19 | GND | Power | Power Ground |
232-
| 20 | D2 | Digital | GPIO |
233-
| 21 | D3/PWM | Digital | GPIO; can be used as PWM |
234-
| 22 | D4 | Digital | GPIO |
235-
| 23 | D5/PWM | Digital | GPIO; can be used as PWM |
236-
| 24 | D6/PWM | Digital | GPIO, can be used as PWM |
237-
| 25 | D7 | Digital | GPIO |
238-
| 26 | D8 | Digital | GPIO |
239-
| 27 | D9/PWM | Digital | GPIO; can be used as PWM |
240-
| 28 | D10/PWM | Digital | GPIO; can be used as PWM |
241-
| 29 | D11/MOSI | Digital | SPI MOSI; can be used as GPIO |
242-
| 30 | D12/MISO | Digital | SPI MISO; can be used as GPIO |
211+
| Pin | **Function** | **Type** | **Description** |
212+
| --- | ------------ | ------------ | ----------------------------------------------------------------------------------- |
213+
| 1 | D13 | Digital | GPIO |
214+
| 2 | +3V3 | Power Out | Internally generated power output to external devices |
215+
| 3 | AREF | Analog | Analog Reference; can be used as GPIO |
216+
| 4 | A0/DAC0 | Analog | ADC in/DAC out; can be used as GPIO |
217+
| 5 | A1 | Analog | ADC in; can be used as GPIO |
218+
| 6 | A2 | Analog | ADC in; can be used as GPIO |
219+
| 7 | A3 | Analog | ADC in; can be used as GPIO |
220+
| 8 | A4/SDA | Analog | ADC in; I2C SDA; Can be used as GPIO **(1)** |
221+
| 9 | A5/SCL | Analog | ADC in; I2C SCL; Can be used as GPIO **(1)** |
222+
| 10 | A6 | Analog | ADC in; can be used as GPIO |
223+
| 11 | A7 | Analog | ADC in; can be used as GPIO |
224+
| 12 | VUSB | Power In/Out | Normally NC; can be connected to VUSB pin of the USB connector by shorting a jumper |
225+
| 13 | RST | Digital In | Active low reset input (duplicate of pin 18) |
226+
| 14 | GND | Power | Power Ground |
227+
| 15 | VIN | Power In | Vin Power input |
228+
| 16 | TX | Digital | USART TX; can be used as GPIO |
229+
| 17 | RX | Digital | USART RX; can be used as GPIO |
230+
| 18 | RST | Digital | Active low reset input (duplicate of pin 13) |
231+
| 19 | GND | Power | Power Ground |
232+
| 20 | D2 | Digital | GPIO |
233+
| 21 | D3/PWM | Digital | GPIO; can be used as PWM |
234+
| 22 | D4 | Digital | GPIO |
235+
| 23 | D5/PWM | Digital | GPIO; can be used as PWM |
236+
| 24 | D6/PWM | Digital | GPIO, can be used as PWM |
237+
| 25 | D7 | Digital | GPIO |
238+
| 26 | D8 | Digital | GPIO |
239+
| 27 | D9/PWM | Digital | GPIO; can be used as PWM |
240+
| 28 | D10/PWM | Digital | GPIO; can be used as PWM |
241+
| 29 | D11/MOSI | Digital | SPI MOSI; can be used as GPIO |
242+
| 30 | D12/MISO | Digital | SPI MISO; can be used as GPIO |
243243

244244

245245

246246

247247
### Debug
248248
On the bottom side of the board, under the communication module, debug signals are arranged as 3x2 test pads with 100 mil pitch. Pin 1 is depicted in Figure 3 – Connector Positions
249249

250-
| Pin | **Function** | **Type** | **Description** |
251-
| ---- | ------------ | ---------- | ------------------------------------------------------------ |
252-
| 1 | +3V3 | Power Out | Internally generated power output to be used as voltage reference |
253-
| 2 | SWD | Digital | SAMD11 Single Wire Debug Data |
254-
| 3 | SWCLK | Digital In | SAMD11 Single Wire Debug Clock |
255-
| 4 | UPDI | Digital | ATMega4809 update interface |
256-
| 5 | GND | Power | Power Ground |
257-
| 6 | RST | Digital In | Active low reset input |
250+
| Pin | **Function** | **Type** | **Description** |
251+
| --- | ------------ | ---------- | ----------------------------------------------------------------- |
252+
| 1 | +3V3 | Power Out | Internally generated power output to be used as voltage reference |
253+
| 2 | SWD | Digital | SAMD11 Single Wire Debug Data |
254+
| 3 | SWCLK | Digital In | SAMD11 Single Wire Debug Clock |
255+
| 4 | UPDI | Digital | ATMega4809 update interface |
256+
| 5 | GND | Power | Power Ground |
257+
| 6 | RST | Digital In | Active low reset input |
258258

259259

260260
## Mechanical Information
@@ -345,41 +345,42 @@ Lors de l’ installation et de l’ exploitation de ce dispositif, la distance
345345

346346
Hereby, Arduino S.r.l. declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states.
347347

348-
| Frequency bands | Maximum output power (EIRP) |
349-
| :------------------------ | :-------------------------- |
350-
| 2402-2480MHz(EDR) | 6.24 dBm |
351-
| 2402-2480MHz(BLE) | 6.30 dBm |
352-
| 2412-2472MHz(2.4G WiFi) | 13.61 dBm |
348+
| Frequency bands | Maximum output power (EIRP) |
349+
| :---------------------- | :-------------------------- |
350+
| 2402-2480MHz(EDR) | 6.24 dBm |
351+
| 2402-2480MHz(BLE) | 6.30 dBm |
352+
| 2412-2472MHz(2.4G WiFi) | 13.61 dBm |
353353

354354

355355
## Company Information
356356

357-
| Company name | Arduino S.r.l |
358-
| --------------- | ---------------------------------------------- |
359-
| Company Address | Via Andrea Appiani,2520900 MONZA |
357+
| Company name | Arduino S.r.l |
358+
| --------------- | -------------------------------- |
359+
| Company Address | Via Andrea Appiani,2520900 MONZA |
360360

361361
## Reference Documentation
362362

363-
| Reference | **Link** |
364-
| ------------------------- | ------------------------------------------------------------ |
365-
| Arduino IDE (Desktop) | https://www.arduino.cc/en/software |
366-
| Arduino IDE (Cloud) | https://create.arduino.cc/editor |
367-
| Cloud IDE Getting Started | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino-web-editor-4b3e4a |
368-
| Forum | http://forum.arduino.cc/ |
369-
| SAMD21G18 | https://ww1.microchip.com/downloads/aemDocuments/documents/MCU32/ProductDocuments/DataSheets/SAM-D21DA1-Family-Data-Sheet-DS40001882G.pdf |
370-
| NINA W102 | https://content.u-blox.com/sites/default/files/NINA-W10_DataSheet_UBX-17065507.pdf |
363+
| Reference | **Link** |
364+
| ------------------------- | -------------------------------------------------------------------------------------------------------------------------------------------------------------------- |
365+
| Arduino IDE (Desktop) | https://www.arduino.cc/en/software |
366+
| Arduino IDE (Cloud) | https://create.arduino.cc/editor |
367+
| Cloud IDE Getting Started | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-arduino-web-editor-4b3e4a |
368+
| Forum | http://forum.arduino.cc/ |
369+
| SAMD21G18 | https://ww1.microchip.com/downloads/aemDocuments/documents/MCU32/ProductDocuments/DataSheets/SAM-D21DA1-Family-Data-Sheet-DS40001882G.pdf |
370+
| NINA W102 | https://content.u-blox.com/sites/default/files/NINA-W10_DataSheet_UBX-17065507.pdf |
371371
| ECC608 | https://ww1.microchip.com/downloads/aemDocuments/documents/SCBU/ProductDocuments/DataSheets/ATECC608A-CryptoAuthentication-Device-Summary-Data-Sheet-DS40001977B.pdf |
372-
| MPM3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
373-
| NINA Firmware | https://github.com/arduino/nina-fw |
374-
| ECC608 Library | https://github.com/arduino-libraries/ArduinoECCX08 |
375-
| LSM6DSL Library | https://github.com/stm32duino/LSM6DSL |
376-
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
377-
| Library Reference | https://www.arduino.cc/reference/en/ |
378-
| Arduino Store | https://store.arduino.cc/ |
372+
| MPM3610 | https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf |
373+
| NINA Firmware | https://github.com/arduino/nina-fw |
374+
| ECC608 Library | https://github.com/arduino-libraries/ArduinoECCX08 |
375+
| LSM6DSL Library | https://github.com/stm32duino/LSM6DSL |
376+
| ProjectHub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
377+
| Library Reference | https://www.arduino.cc/reference/en/ |
378+
| Arduino Store | https://store.arduino.cc/ |
379379

380380
## Revision History
381381

382382
| Date | **Revision** | **Changes** |
383383
| ---------- | ------------ | ------------------------------------- |
384+
| 27/10/2023 | 3 | Correction NINA SPI pins |
384385
| 03/08/2022 | 2 | Reference documentation links updates |
385386
| 15/04/2021 | 1 | General datasheet updates |

0 commit comments

Comments
 (0)